1PC 380v 4.5kw ER32 air-cooled spindle motor without mounting flange 4 bearings

Size: 201x103x120.5mm

Speed regulation mode: change the spindle speed through the three-phase output inverter and adjust the frequency of the inverter.

Cooling method: air cooling

Power interface: optional 5-pin waterproof aviation plug. Aviation plugs are marked with "1", "2", "3", "4", "5", "GND". "1", "2", and "3" are connected to the inverter (U, V, W), and "GND" is connected to the inverter ground. )

Power: 3.5kw (1HP=0.735w)

Voltage: 380v (please leave a message if you need a 220v spindle, thank you)

Current: 15.8A

Frequency: 0-300Hz

Speed: 0-18000rpm

Torque: 2.39Nm

Jump close: less than 0.01mm

Shaft end connection: ER32-Φ3.175-Φ20

Bearing type: 2*7008C P4, 2*7002C P4 (4 ball bearings)

Chuck: ER32

Clamping tool diameter: 17mm, 16mm, 15mm, 14mm, 13mm, 12.7mm, 12mm, 11mm, 10mm, 9mm, 8mm, 7mm, 6.35mm, 6mm, 5mm, 4mm, 3.175mm, 3.0mm, 2, 5mm, 2.0 mm, 1.5mm, 1mm (Standard 4mm)

Grease lubrication

Main use: Carving wood, bamboo, ordinary PCB, PVC, PMMA, plastic, two-color board (ABS) and other non-metals, and also can carve soft metal surfaces such as gold, silver, copper, aluminum, and lead. (Please note that this is a woodworking spindle, which can only be used for woodworking and aluminum products, not steel products. If you need steel products, please check the metal spindle, thank you!)

●The working environment temperature of the spindle is usually -10~40.

●Before installing the first electric spindle to rotate the spindle head by hand, you should feel flexibility and no blockage.

P4 fully sealed angular joint bearings can extend the life of the spindle.

The longer the length, the greater the torque and the greater the power.

Careful assembly makes the spindle more precise.

The accuracy is 0.01mm, and the coaxial cable is less than 0.0025mm

1. Our main shaft uses 4 bearings.

2. Bearings are resistant to high temperature and low heat

3. The ball bearing has low friction, low noise and long service life.

5Pins Air Plug: No.1,2,3 connecting to Inverter U,V,w. Spindle Gnd connecting to Inverter Gnd.

ER32 Collet Nut balancing nut high grinding inner cone precision 0.01mm.

●When the spindle is stored and transported, the bearing condition inside the high-speed grease will change, and the customer should run it at low speed for 30 minutes. Then increase slowly at a speed of 3000 rpm, running for 20 minutes each time. The spindle and inverter should work together. The specifications and parameter settings of the inverter match the spindle parameters.

●To connect the inverter main shaft, the three-phase inverter power cord should be welded to the plug 1 (U), 2 (V), 3 (W) pin, and the grounded pin 4. After turning on the power, observe whether the spindle rotation axis always shows the direction. If it is inconsistent, turn it off immediately, and replace the two wires of the three-phase power supply connected to the inverter and the spindle.

●Before using the spindle every day, it must run at low speed for 15-20 minutes. Clamp the cutter on the spindle, the chuck nut, chuck, and cutter must be clean enough. The shank inserted into the chuck must be larger than 15mm.

Company information and contact information

Jinan Hongyang CNC Machinery Co., Ltd. was established in 2008. There are more than 100 employees, and the inventory area is 10,000 square meters. It is mainly engaged in engraving machine parts, including spindle motor, frequency converter, stepper motor, drive, hybrid servo motor, servo motor, Richauto dsp series controller, weihong or nc studio controller, spindle cooling water pump, lubricating oil pump, tool sensor, Limit sensors, water-cooled vacuum pumps, air-cooled vacuum pumps, power supplies, transformers, gear boxes, racks, rails, sliders or blocks, ISO30 tool clips, cable chains, spindle dust covers, vacuum cleaners and other engraving machine accessories, welcome your For inquiries.

Contact information

WeChat whatsapp mobile 8615650000988

lily @ hycncrouter. com