+
41g Happymodel Crux3 115mm 4in1 AIO CrazybeeX 5A CADDX Ant EX1202.5 KV6400 1-2S 3inch Toothpick FPV Racing Drone DIY Toys
Specification:
Brand Name: Happymodel
Model: Crux3
Item Name: 115mm F4 OSD 1-2S 3 Inch Toothpick FPV Racing Drone
Wheelbase: 115mm
Size: 97x97x35mm (without propellers)
Optional Receiver Version:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
Internal SPI DSM2/DSMX version(Compatible with Spektrum or Multiprotocol DSM2/X radio)
External Frsky RXSR receiver version(ACCST D16 sbus output)
External TBS Crossfire Nano receiver version
Weight: 41g (without battery)
Recommend Lipo Battery: 2s 350mah/400mah/450mah/520mah Battery ( NOT Included)
| EX1202.5 6400KV Motor | Configu-ration:9N12PStator Diamter:12mmStator Length:2.5mmShaft Diameter:Φ1.5mmMotor Dimension(Dia.*Len):Φ14*14.5mmWeight: 4.4gNo.of Cells(Lipo):1-2S |
Gemfan 3018 2-Blade Propeller | Center Thickness:5.5mm Prop Diameter:76.5mm Center Hole diameter:1.5mm |
| CrazybeeX FR V2.2 F4 Flight Controller | MCU: STM32F411CEU6 (100MHZ, 512K FLASH)Sensor: MPU6000 (SPI connection)Board Size: 28.5x28.5mmPower Supply: 1-2S battery input (DC 2.9V-8.7V)Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 readyBuilt-in Betaflight OSD(SPI Control)Built-in 5.8G VTXBuilt-in SPI Frsky/Flysky receiver or no receiverBuilt-in 5V 1A BEC (Frsky SPI RX Version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR (Flysky SPI RX Version) CRAZYBEEX FS V2.2 FC Firmware target: CrazybeeF4FS (DSM2/X SPI RX Version)CRAZYBEEX DXS V1.0 FC firmware target: CrazybeeF4DXS (External Frsky RXSR Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX (External TBS CRSF NANO Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX |
| Onboard 5A BL_S 4in1 ESC | MCU upgraded to EFM8BB21Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds)Support BLHeliSuite programmableFactory firmware: S_H_50_REV16_7.HEXDefault protocol: DSHOT600 |
Onboard Frsky SPI D8 Receiver Version | SPI BUS receiver Frsky D8 compatibleCompatible Non EU transmitter D8 model Channels: 8chFailsafe supportNo ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m |
Onboard Flysky SPI receiver Version | Protocol: AFHDS and AFHDS-2A SwitchableChannels: 8ch(AFHDS) or 14ch(AFHDS-2A)No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m Failsafe support |
Onboard DSM2/X SPI receiver Version | SPI BUS receiver DSM2/DSMX compatible Channels: Max 12chFailsafe supportNo ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m RSSI enable (show on the goggles) |
External Frsky R-XSR receiver version | Weight: 1.5g Number of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel) Operating Voltage Range: 3.5V~10V Operating Current:70mA@5V Firmware Upgradable Compatibility: FrSky X Series modules and radios in D16 mode Could support Frsky New ACCESS Protocol ( Upgrade firmware) |
External TBS CRSF Nano receiver version | Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible |
| Onboard 5.8G 40CH 25/200mW VTX | Output power: 25mw~200mw switchableFrequency: 40CHInput voltage: 3.3V 5.5VCurrent consumption: 300mA(type)Frequency: 5.8GHz 5bands 40 channelsWith Race band Smartaudio ready |
Caddx ANT 1200TVL Camera | Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC or PAL Switchable IMAGE: 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio : >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm Min. Illumination: [email protected] Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14*14mm(with bracket to 19*19mm) Wide Power Input: DC 3.7-18V Work Temperature: -20℃~+60℃ Weight: 2g (N.W.) |
Features:
- 41gram 1-2s brushless Toothpick drone
- New AIO 4in1 CrazybeeX flight controller
- CADDX ANT 1200tvl Camera
- New 1202.5 brushless motor
- XT30 connector
- Compatible with Insta360 Go Camera ( this camera is NOT Included, you can add it by yourself.)
Pacakge Included:
1x Crux3 Frame and Canopy1x Optional Receiver
1x F4 Flight Controller AIO 5A ESC Board
1x 5.8G 25-200mW VTX ( built-in Flight controller)
4x Happymodel EX1202.5 6400 KV Motor
4x Gemfan 3018 Propeller CW
4x Gemfan 3018 Propeller CCW
1x Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera
1x Screw Driver
1x Propeller Disassemble Tool
1x Happymodel Handbag
Controller Mode : MODE1,MODE2
Origin : Mainland China
Recommend Age : 12+y
Control Channels : 8 Channels
Video Capture Resolution : Other
Indoor/Outdoor Use : Indoor-Outdoor
Material : Plastic
Aerial Photography : Yes
Camera Mount Type : Fixed Camera Mount
Controller Battery : as show
Flight Time : as show
Dimensions : as show
Model Number : Happymodel Crux3
Warranty : as show
Package Includes : Original Box
Remote Distance : over 5km
Operator Skill Level : Beginner
Warning : as show
Remote Control : Yes
State of Assembly : Ready-to-Go
Charging Voltage : 12v
Motor : Brushless Motor
Charging Time : 2 hours
Plugs Type : as show
Power Source : Electric
