【Features】:

◆The operation is simple, and the dent can be quickly restored directly for you.

◆Repair without baking lacquer dents, no damage to the original paint, fast, money-saving and environmentally friendly.

◆Three different sizes of traction shim strips are suitable for dents of various sizes.

◆Suitable for automobile surface sheet metal, refrigerator, washing machine surface sheet metal.

◆Suitable for all kinds of flat metal recessed places.

The product contains one glue gun, three glue chains, one nut, one bracket, and one glue stick.

1. Clean the dent part with a clean damp cloth;

2. Load the hot melt glue stick from behind the hot melt glue gun, pull the trigger, let the glue stick enter the glue gun, plug in the power supply, and let the glue gun warm up for 5 minutes;

3. Find a suitable traction pad (large dents require a large traction pad; (note: the larger the traction pad, the greater the pulling force);

4. Pull the trigger of the glue gun and apply the extruded glue to the selected traction gasket (the 4 holes of the gasket should also be covered with hot melt glue)

5. Quickly place the traction pad covered with hot melt adhesive on the center of the dent, and gently press it until the hot melt adhesive is solidified and adhered firmly; (Let the hot melt adhesive dry for about 8 minutes; we recommend not to let the hot melt adhesive dry for about 8 minutes; Do not dry the glue for more than 10 minutes)

6. Align the hole in the middle of the traction tension bridge with the sticky traction washer rod, put the screw rotation button on the traction washer rod, and slowly tighten it until the dent part is pulled to be flush with the surrounding surface. .

7. For some dents, it may be necessary to repeat the above steps several times to repair the dents.

8. If the surface to be repaired is raised a little, please follow the steps below: First, rub the raised points back and forth with your thumb until the raised points are as flat as other surfaces; if the raised points cannot be restored flat with your thumb, use Tap the stick (holding the pen) to gently tap the raised point until the raised point becomes flat. Sometimes, it may need to be repeated several times. (Note: When using the percussion stick, do not use too much force)

9. After the dent is repaired, unscrew the screw knob, remove the traction bridge, and then remove the traction washer. If there is hot melt glue sticking to the surface of the car body, just gently tear it off with your hands.

1. Clean the dent part with a clean damp cloth;

2. Load the hot melt glue stick from behind the hot melt glue gun, pull the trigger, let the glue stick enter the glue gun, plug in the power supply, and let the glue gun warm up for 5 minutes;

3. Find a suitable traction pad (large dents require a large traction pad; (note: the larger the traction pad, the greater the pulling force);

4. Pull the trigger of the glue gun and apply the extruded glue to the selected traction gasket (the 4 holes of the gasket should also be covered with hot melt glue); (Figure 1 below)

5. Quickly place the traction pad covered with hot melt adhesive on the center of the dent and gently press it until the hot melt adhesive is solidified and adhered firmly; (let the hot melt adhesive dry for about 8 minutes; we recommend not to let the hot melt adhesive dry for about 8 minutes; Do not dry the glue for more than 10 minutes; the drying time in winter is slightly shorter.) (Figure 2 below)

6. Align the hole in the middle of the traction tension bridge with the sticky traction washer rod, put the nut knob on the traction washer rod, and slowly tighten it until the dent part is pulled to be flush with the surrounding surface; (Figure 3 below)

7. For some dents, it may be necessary to repeat the above steps several times to repair the dents;

8. If the surface to be repaired is raised a little, please follow the steps below: First, rub the raised points back and forth with your thumb until the raised points are as flat as other surfaces; if the raised points cannot be restored flat with your thumb, use Tap the stick (holding the pen) to gently tap the raised point until the raised point is flat. Sometimes, it may need to be repeated several times. (Note: When using the percussion stick, do not use too much force)

9. After the dent is repaired, unscrew the nut knob, remove the traction tension bridge, and then remove the traction washer. If there is hot melt glue sticking to the surface of the car body, just gently tear it off with your hands.