PowMr LiFePo4 3.2V 4S~24S 15A~60A PCM PCB 18650 Battery Pack Protection Board Balanced BMS Used For E-Bike Scooter,E-Motorcycle

Product Description:Model:4S~24S (3.2V Rated LiFePO4 not for 3.7V rated Li-ION Battery)common Version : common port for charge/discharge We can customize any PCB from 1S to 30S lithium batteries with different current.1. Overview◆BMS 4S~24S 12V 24V 36V 48V 60V 72V 15A 20A 30A 40A 50A 60A◆We can design it for various lithium batteries like LiFepo4, LiMn2O4, and Li-polymer etc.◆The main functions are: over charge protection, over discharge protection, over current protection, short-circuit protection, temperature protection etc.◆According to the customer request we can develop PCM in different sizes and structures.◆BMS manufactured by high quality Mos and IC imported . Keep your battery long cycle serivce life time.2. Advantage◆Use top quality (A-level) protective integrated circuit IC, from the solution of Seiko of Japan.◆Strong load ability, constant discharge current 15A/20A/30A/40A/50A/60A, use high voltage resistance, low inner resistance power Mosfet. The heat sink will greatly help cooling.◆IC itself has power balancing function. The circuit is simple and reliable.◆Typical voltage detection for each cell. So each battery will be prevented over charged or over discharged. Over current and short circuit protection function is very reliable.Long time short circuit of the load won’t affect the PCB and the battery.Temperature protection during charging and discharging.◆Extreme low power consumption. The consumption of the whole device is less than 50uA.◆PCB use high anti-corrosion, high water resistance, high impedance ESD conformal Coating.

3.FAQ4.1 Which current of the PCB should i choose?  Take 13S 48V pack as an example: Which PCB you should choose depends on the power of your motor or the current limitation of your controller. Below 350W ,you can choose 16A.Below 500W, you can choose 18A, Below 800W, you can choose 35A,Below 1KW, you can choose 60A. Above 1200W, the same. If you are not sure, please contact us freely.2 Can I use bigger size of PCB than it should?Suppose you need 60A PCB but you chose 80A, that is OK.80A allows higher current.Nothing bad but a bit higher price.But if you choose 50A, sorry it is too small. So you can choose higher spec but can’t choose lower one than it should have been.3 What kind of charger should i choose?Lithium battery must be charged by lithium battery charger. You can’t charge it with a lead acid battery charger. The lead acid battery charger might damage MOS pipe of the PCB.4 If i have PCB, do i need any balancers?Yes if you can add QNBBM balancers, that would be perfect.The Main function of PCB is to prevent batteries from over charged or over discharged,over heated etc.All the PCB /BMS in the world balance performance is not satisfactory.With balancers added, the batteries lifespan will be longer and the capacity will be fully used.5 How to judge if my PCB is broken or not ?If you’d like to judge if the PCB is fine or not, please use a multi-meter and see if the voltage of each cell is close to each other or not.when the volt difference is 1V, the battery will have such performance:driving distance is short, cut off when started, charging time is very short.under such situation , some battery is defective. When the PCB is broken, the battery can’t be discharged when you measured the battery volt is normal.   4.Technical parameter（ for 3.2V rated Lifepo4 battery,If your battery is 3.7V LiPO/LiNCM battery,please leave message to us.We can adjust the parameters）Our BMS are mainly used in li-ion power batteries and energy storage lithium vattery.Widely used in electric scooter,e-bike,tourist sightseeing vihide,electric tricycle,low speed ev,emegency UPS,solar street light,RV & Home energy storage ect.